Lithium-ion Battery Pack Calculator
From cell count to runtime in one place, with an engineer’s reply within 24 hours.
Choosing a pack is easier with the numbers in front of you. Lay out the cells, test your load, then pass the figures to our engineers so the first reply already fits your project.
Whether you need a fully custom pack, a standard design, or a second opinion on a quote you already hold, we work from your figures and suggest a practical route.
- Compare series and parallel layouts before you commit
- See runtime against a realistic duty cycle
- Send one summary instead of retyping specs
Worked examples and tips: Lithium Battery Calculator Guidance
Series/Parallel Battery Pack Builder
Pick a cell, choose how many go in series and in parallel, and read off the pack’s rated voltage, capacity and energy.
A typical voltage is filled in when you pick a chemistry. Replace it with the figure on your cell’s datasheet.
More cell specs (optional)
These only add a voltage range, a weight and a current line to the result. The current line ignores the BMS, wiring, heat and connectors.
Pack result
3S2P
Total cells
–
Rated voltage
–
Rated capacity
–
Stored energy
–
–
A planning figure, not an approved design. Discharge limits, usable energy, charger match and shipping class still need an engineer’s check.
Battery Pack Runtime Estimator
Enter what your device draws to see how long the pack lasts, or enter the hours you need to see how big the pack must be.
The 80 % and 90 % shown are starting guesses. Replace them with figures from your cell data and your converter. Efficiency only applies when the load is given in watts.
Runtime result
Runtime
–
In hours
–
Usable energy
–
Share of rated energy you can actually use
A planning figure only. Nothing here allows for cold, ageing, load peaks or high-rate losses, so check it against cell test data.
Send the Numbers to Our Engineers
Both results travel with your enquiry automatically, so there is nothing to copy or retype. This is exactly what we will receive:
Your details
How Each Figure is Worked Out
| Figure | How it is worked out | Keep in mind |
|---|---|---|
| Total cells | S × P | Treats every cell as identical. |
| Rated voltage | S × voltage per cell | Real voltage rises and falls with charge level and load. |
| Rated capacity | P × capacity per cell | A label value, not a measured one. |
| Stored energy | Rated voltage × rated capacity | Before temperature, ageing and conversion losses. |
| Average load | Running load × share of time running + idle load × the remainder | Short peaks are smoothed into one average. |
| Pack draw | Load ÷ efficiency (watts), or amps × pack voltage (amps) | A single efficiency figure stands in for a whole curve. |
| Runtime | Stored energy × usable share ÷ pack draw | No correction for cold, age or high discharge rate. |
| Energy needed | Pack draw × hours needed ÷ usable share | Add your own safety margin on top. |
Things to Check Before You Finalize a Design
Voltage window
Compare full-charge and cut-off voltage with what your device accepts, not only the nominal figure.
Current and protection
Note continuous, start-up and peak current, then size the BMS, wiring and connectors as one system.
Temperature
Charging and discharging have separate temperature limits, and neither tool corrects for heat or cold.
Cell type
Lithium-ion and sodium-ion cells differ in voltage, energy density and low-temperature behavior, so confirm the cell suits your use.
FAQs about Lithium-ion Battery Pack Calculator
Can I use this calculator for LiFePO4 or sodium-ion cells?
Yes. The arithmetic is the same for any chemistry, but you must enter the nominal voltage from your cell datasheet. Choosing a chemistry fills in a typical value as a starting point only.
Does the estimate cover cold or hot conditions?
No. Neither calculator applies a temperature factor. Available capacity changes with temperature, load and ageing, so include your operating temperature range when you contact our engineers.
How do I calculate battery pack voltage, capacity and energy?
Pack nominal voltage is the number of cells in series times the cell nominal voltage. Pack capacity is the number of cells in parallel times the cell capacity in Ah. Nominal energy in Wh is pack voltage times pack capacity. For example, a 10S4P pack of 3.6 V 5 Ah cells gives 36 V, 20 Ah and 720 Wh.
What usable capacity and efficiency should I enter?
The defaults of 80 percent usable capacity and 90 percent efficiency are planning placeholders, not datasheet values. Use the discharge cut-off and rate data for your cell, and the efficiency of your converter or motor driver at your real load. If you enter the load as current at the battery terminals, efficiency is already included.
What does 3S2P mean in a battery pack?
3S2P means three cells in series and two in parallel, so six cells in total. Series groups add voltage and parallel groups add capacity. The label alone does not define a full battery specification, because cell model, chemistry, protection and interface still have to be chosen.
Does the Wh figure decide shipping eligibility?
No. Transport classification also depends on chemistry, test reports, packaging, quantity and state of charge.
Can I choose a BMS from these numbers?
Not on their own. BMS selection depends on the true load profile, protection timing, wiring and heat dissipation.
How quickly will CMB reply to my email?
Our target is to respond with personalized battery pack suggestions within 24 hours of receiving your enquiry.
How is battery runtime estimated?
Runtime is the usable energy divided by the average power drawn from the pack. Usable energy is the nominal energy multiplied by the usable capacity percentage. When the load is entered as power at the device, conversion efficiency raises the power drawn from the pack. Duty cycle and standby load are blended into one average.
Is a 10-cell NMC pack automatically a 36 V replacement?
Not necessarily. Ten cells at 3.6 V give 36 V nominal, but the charge voltage, cut-off voltage and device limits must also match.
How do I calculate battery runtime from voltage, Ah and load?
First convert the pack rating to watt-hours by multiplying nominal voltage by capacity in amp-hours. Apply an evidence-based available-energy factor and reserve, then divide the resulting planning energy by the average power drawn from the battery. If the load value is measured on the device side, account for conversion losses.
Does the estimated runtime guarantee that my battery pack will power the equipment?
No. The estimate is an energy-planning result, not a battery design approval. Confirm the full voltage range, continuous and peak current, BMS protection settings, thermal conditions, connectors, wiring, charging requirements and end-of-life performance in the actual equipment.
We Are Ready for Your Project
Our experts with 18 years of battery experience can help you select the best battery for your application. We don’t just build battery packs — we engineer reliable power solutions backed by transparent manufacturing, certified quality, and a commitment to sustainability.
